Details for Error code E18/0102

Cold solderjoint - CPU/GPU/RAM



3 red lights

 
Details
Primary Error code:3 red lights 3 RLOD
E-Code / Secondary Error code:E18 (No Audio/Video) / 0102
Binary/Hex:00010010 / 0x12 -> 18
Known fixes:

1) X-Clamp replacement
2) Reflow GPU and RAM

Related Errors:
Powered by X-EX.com 
No Related Errors available!
Description:

This error is caused by a cold solder joint under CPU, GPU or one of the RAM bricks. Can also be a component that is missing or damaged so look for missing parts near the GPU.

References:
No References available!
Clicks:324083
Share(BBCode):

 
 

Comments for this Error code:

on 2019-06-19 05:04:48 :

Had a box with 0020, then this. If I push down on the RAM chips under the GPU
heatsink, boots. If I let go, artifacts. Quickly push down, they go away. If
this happens to you, reflow RAM under GPU heatsink and you should get green
boot.

 

on 2014-07-01 08:28:05 :

A2 zephyrs recently screwed themselves with this error recently. Ececpt they had
nothing to do with any chip. Believe it or not, a cap or multiple caps burned
up. It was running fine, then I started to hear a weird sizzling liquid sound
for about 10 minutes, then the screen froze, restarted it to this error and more
sizzling sounds. Crazy weird. Otherwise the other 99% of the time this error is
just the GPU in need of reball.

 

on 2013-04-01 14:28:11 :

0102 on a Xenon board. Appears to be one of the RAM chips for me. It's the
one to the front of the console, left-most chip, not the ones under the
heatsink. Penny fix & GPU bake should do it.
/JYP666
Need help? Visit my FB group http://www.facebook.com/groups/yorkrepairs/ and
leave me a message. Based in York, UK.

 

on 2012-10-07 20:11:40 :

Hey so i keep getting this problem.. I've already redid heatsinks thermal
paste on both GPU and CPU, and it seems to work fine for about 10 min, then it
goes back to this error. So far I've fixed it by unplugging fans till it
hits 2 RROD, then restart it and it works.. but then repeat error. I have a
newer drive in it, could that be a problem?

 

on 2012-03-31 02:43:32 :

Thanks to goodolick pressure on cpu gets green lights no pressure gets rrod.
Took it apart scraped off old thermal paste cleaned put new artic silver and
thanks to tomi_the_great unplugged fans let run till 2 red lights, cooled down
and booted right up works fine again.

 

on 2012-03-17 08:39:55 :

replaced capacitor c9e3 and fixed a recurring issue ..

 

on 2012-02-23 22:02:56 :

this code kept coming back and i just couldnt get rid and also the drive was
knackered however ive just tried my new dry reflow profile (not recommended) and
its fireing up was abit techy for the first five minutes fans running really
high but now its running better than ive ever had it ill keep you posted with
the results.

 

on 2012-01-06 00:15:49 :

I have a 0102, I tried reflowing everything but it still report a 0102.. There
is a little scratch in the motherboard, but i don't think its cutting any
track. Anyway, what else can i do? if it cuts a track how to repair it?

 

on 2011-09-09 07:45:38 :

okay, i have this error, but i dont know how to fix it. Ive done the Xclamp
method and it is still broken. could someone please tell me what to do, as i
dont want to go lookking for an answer which wont be perminent

 

on 2011-08-05 04:32:38 :

Successfully repaired by reballing GPU with ZT-7.

 

on 2011-07-30 16:01:34 :

Can confirm sometimes CPU. Had a reballed GPU Xenon come back to me. After
another reflow of GPU still 0102. Was about to replace GPU when decided to do
further testing. Pressure on ram chips still yielded 0102. Pressure on CPU
produced green lights. Reflowed CPU and the xbox is now stable.

 

on 2011-07-30 16:01:17 :

Can confirm sometimes CPU. Had a reballed GPU Xenon come back to me. After
another reflow of GPU still 0102. Was about to replace GPU when decided to do
further testing. Pressure on ram chips still yielded 0102. Pressure on CPU
produced green lights. Reflowed CPU and the xbox is now stable.

 

on 2011-07-06 11:02:15 :

Had a board with 0102 error.
Reballed the GPU but still 0102.
Then I've tried to reflow everything except ANA and SB but still 0102.
I've solved it by reflowing again the reballed GPU!
For sure one of the balls didn't attach properly!

 

on 2011-03-28 02:17:23 :

The southbridge can also be a cause of this error code. I had one today that was
fixed by a reflow of the southbrige.

 

on 2011-03-10 02:39:21 :

Hello,

I have a E18 code on this xbox here.
I had it gone for a few seconds, but ever since it doesn't dissapear.
I did the x-clamp fix, reflow CPU, GPU and all RAM chips.
Anybody got any more suggestions?
Please advise.

 

on 2011-02-08 20:45:21 :

so i opend my xbox and i remove the x-clamps and i see on tiny recister missing
under the CPU. how can i fix it? if u have the answer can u tell me. e-mail
killermarioj@yahoo.com

 

on 2010-12-07 23:25:43 :

Fixed over a hundred of these with no problems. The GPU just needs to be
reflowed using the profile available on here, but you need to leave the griddle
on for 30 minutes after the repair. It works everytime. Like I said, over a 100
of these and not one return in 9 months!

 

on 2010-11-20 21:42:38 :

O1O2 ALSO can be scratched trace on board under gpu due to removing x-clamps
with screwdriver

 

on 2010-09-29 21:58:48 :

If I do the aluminum sheet fix, where do I put it? I assume between the GPU and
the Heat sink?

 

on 2010-08-15 14:04:42 :

reflow for 5-10 minutes with fan turned off works for me. after 5 minutes i turn
off the sexbox and turnit on again and the 2rrod shown.

i noticed that overheat in GPU cause this 0102 error. So afterthat i make a
paper trik (spliting vent) and play sexbox with open tray and home fans blows
direct on gpu n cpu. because when the 3rrod 0102 occur, i noticed that the air
from the sexbox quite hot.

with this mod, i play 10 hour (2 hour idle) without suffer any overheat, and
crash.

i play GTA4.

 

on 2010-08-15 14:00:30 :

reflow for 5-10 minutes with fan turned off works for me. after 5 minutes i turn
off the sexbox and turnit on again and the 2rrod shown.

i noticed that overheat in GPU cause this 0102 error. So afterthat i make a
paper trik (spliting vent) and play sexbox with open tray and home fans blows
direct on gpu n cpu. because when the 3rrod 0102 occur, i noticed that the air
from the sexbox quite hot.

with this mod, i play 10 hour (2 hour idle) without suffer any overheat, and
crash.

i play GTA4.

 

on 2010-08-03 14:03:10 :

hi guys
i have this error code on an xbox and ficed it multiple times but it keeps
coming back after a week or sow:s does anybody now how i can fix this, i have
done the x-clamp replacement, heatgunt it at 500 degrees celcius, i cut the temp
trace beceause that was an error to and i did a 12 volt fan mod. but it keeps
coming back, does anybody know what i'm doing wrong?? please help

 

on 2010-08-03 13:31:37 :

hi guys
i have this error code on an xbox and ficed it multiple times but it keeps
coming back after a week or sow:s does anybody now how i can fix this, i have
done the x-clamp replacement, heatgunt it at 500 degrees celcius, i cut the temp
trace beceause that was an error to and i did a 12 volt fan mod. but it keeps
coming back, does anybody know what i'm doing wrong?? please help

 

on 2010-08-03 13:31:23 :

hi guys
i have this error code on an xbox and ficed it multiple times but it keeps
coming back after a week or sow:s does anybody now how i can fix this, i have
done the x-clamp replacement, heatgunt it at 500 degrees celcius, i cut the temp
trace beceause that was an error to and i did a 12 volt fan mod. but it keeps
coming back, does anybody know what i'm doing wrong?? please help

 

on 2010-06-09 04:15:37 :

This is the most common error code that I see in all the xboxs I repair. About
55-60% of the 3RROD units has this 0102 secondary error code. It is caused by a
cold solder joint underneath the GPU. Heatgun/Griddle will repair these if you
know what you are doing.

 

on 2010-04-19 02:13:29 :

I wouldnt suggest putting an aluminum sheet on your gpu. The only reason this
might work is if the heatsink is scratched up. try sanding down your heatsink
with really fine sandpaper. Also Griff, a hair dryer is now going to help. There
is no way the chip will ever get hot enough. Solder has to reach about 220C to
melt. Thats around 500F.

I have fixed several systems with this error. reflowing the cpu and gpu and
replacing the thermal paste has worked every time for me. I have yet to have one
of these that I couldnt fix

 

on 2010-04-03 21:28:26 :

Here you can enter your comment...

 

on 2010-03-27 22:47:11 :

I just was attempting to fix an xbox 360 with a gpu error by reflowing the top
and bottom of the gpu chip. Then, when i put everything back together, the error
was replaced with this. Would this be an easy fix. I have a heatgun, artic
silver 5, and penny's to replace thermal pads. All i ned to know is which
out of all of those will fix this error :D

 

on 2010-01-23 21:27:00 :

Have to say i've cooked my MB in oven, changed thermal paste and still get
the RROD 0102. Used aluminum foil on GPU as a last attempt. It works perpectly.

 

on 2010-01-23 21:26:43 :

v

 

on 2010-01-16 04:25:13 :

Replace thermal paste. 98% of the time, that is the problem. One of the
heatsinks are touching their chip. No X-clamp Mod necessary. Just replace the
thermal paste with Arctic Silver 5.

 

on 2009-12-15 01:12:31 :

Penny fix then heat with classic heirdryer is help me )

 

on 2009-12-11 23:23:14 :

adding an a piece of aluminum sheet to the gpu usually fixes this problem.

 

Add a new comment:

Remaining characters:

Anti-spam: Captcha



Copyright Information: Lately it has come to our attention that more and more people stole content from this Error code Database without giving credit, some also restricted access to this information and demanded a payment, we would like to point out that it is perfectly fine to republish content from XE on other sites, however we demand a link back to this error code database and the information must be freely and non commercially available, we appeal to those who feel addressed, add a link and respect the work of others, thank you...

Notice: None of this is official, the methods have often been proven to work but success cannot be guaranteed, you do it on your own risk!
If your console is still covered by the 3 year warranty use it because Microsoft will fix it for free!
A lot of the information you are getting here has been collected in the community, so thanks to everybody who shared his misery!




Back
 
 
 

 
 
 

Xbox Repair Guide

Please select the number of (red) lights that your ring of light shows:

0 red lights
0
 
1 red light
1
 
2 red lights
2
 
3 red lights

4 red lights
4
 


or

Error codes

Go straight to the Error code list/ Database!